AGILENT U2761A DRIVER DOWNLOAD

Check Your System Prior to any installation or configuration, please ensure that your PC meets the following minimum system requirements. Then, start drawing the desired waveform. Input the to save the file. If there are any missing or mechanically damaged items, contact the nearest Agilent Sales Office. Features and Functions Soft Front Panel Operation On the Offset panel as shown in desired offset value and select the unit from the drop down list. In This Guideā€¦ Getting Started In this chapter, you prepare your system for installation and configuration to get started with the UA. B Pass – Temporary degradation, self recoverable.

Uploader: Kajikree
Date Added: 4 September 2005
File Size: 68.77 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 23700
Price: Free* [*Free Regsitration Required]

Table of Contents Add to my manuals Add. The default carrier frequency is 1 kHz for all functions.

Index of /Companies/Agilent/UA

Output Termination Features and Functions Output Termination This configuration applies to output amplitude and offset voltage only. The default value is 1 ms. The default is 1 kHz for all functions. The following SCPI commands show a sample procedure of generating output.

In AM, the amplitude of the carrier is varied by the instantaneous voltage of the modulating waveform. To enable or disable the grid reference, click.

To output the AM waveform, configure the settings for the carrier frequency, modulating frequency, depth, output amplitude, offset voltage, and the desired waveform.

To output the PM waveform, configure the settings for the carrier frequency, output amplitude, offset voltage, modulating frequency, phase deviation, and the desired waveform. Features and Functions 8 Saving the waveform.

  LENOVO Q965 AUDIO DRIVER DOWNLOAD

U2761A USB Modular Function Generator IVI Instrument Drivers

To disable this dialog, select the Never show this dialog option in the Show this dialog panel and click 9 For modules other than the UA Series, UA Series, UA Series, and UA, the system will perform a firmware version check on your connected Duty Cycle square Waves Features and Functions Duty Cycle Square Waves The duty cycle of a Square wave represents the amount of abilent per cycle gailent the Agilejt wave is at a high level assuming that the waveform is not inverted.

Check Your System B. Features and Functions Function Limitations If you change to a function where the maximum frequency is less than the current function, the frequency will be adjusted to the maximum value for the new function. To output the PSK waveform, configure the settings for the carrier frequency, output amplitude, offset voltage, deviation, and PSK rate. Features and Functions Limits Due to Units Selection In some cases, the amplitude limits are determined by the output units selected.

The maximum carrier frequency depends on the selected gailent as shown below. Remote Interface Operation FM: Click to begin the freehand draw mode or enable line draw mode. An example of the AM waveform is shown in Figure 2- You can sweep up or down in frequency, and with either linear or logarithmic spacing.

Agilent UA Instrument Driver – MATLAB & Simulink

Page Features and Functions 8 Saving the waveform. The duty cycle setting applies only to a Square waveform carrier. When enabled, the Output button is illuminated. In FM, the frequency of the carrier is varied by the instantaneous voltage of the modulating waveform. This may occur when the units are Vrms or dBm due to the agillent in crest factor for the various output functions. Page Or visit Agilent worldwide web at: Below shows an example of the FM waveform.

  HP OFFICEJET D145 DRIVER DOWNLOAD

To output the FM waveform, configure the settings for the carrier frequency, output amplitude, offset voltage, modulating frequency, deviation, and the desired waveform. Page 45 Features and Functions Function Limitation If you change to a function where the maximum frequency is less than the current function, agilennt frequency will be adjusted to the maximum value for the new function.

Page Index limits amplitude duty cycle frequency function offset voltage output termination units selection L-Mount kit output amplitude control frequency function SCPI commands sweep termination units phase noise carrier frequency carrier waveform modulating waveform modulating waveform frequency phase deviation SCPI commands prerequisites product dimensions Symmetry represents the amount of time per cycle that the Ramp wave is rising assuming that the waveform is not inverted.

Comments to this Manuals Your Name. The UA begins at the start frequency, sweeps to the stop frequency, and then resets back to the start frequency.

For a logarithmic sweep, the UA varies the output frequency in a logarithmic fashion.